Try the following:

1. Download Meilhaus Electronic Port Devices Driver Windows 10
2. Download Meilhaus Electronic Port Devices Driver Win 7
3. Download Meilhaus Electronic Port Devices Driver Ed

The isolator is fully transparent (like a cable) between the PC and a USB device, so no additional drivers or other software is required. Combines the functions of the isolator ME-USB Iso with a quad hub. Galvanic isolation of the USB connection (Note: USB 2.0 full-speed only) between a PC and USB devices. Supply power from external power supply. Drivers & Downloads Visit to the above 3. Windows Drivers & Downloads; 6. Windows Server™ 2003 R2. Information on Windows Server™ 2003 R2. ServerView for TX150 S2/TX150 S4/TX200 S2/RX100 S2/RX100 S3/RX200 S2/RX300 S2/RX600 S2/BX620 S2 Note. Update information for PRIMERGY FT-model.

Download Mobile Phones drivers for Windows, firmware, bios, tools, utilities. Converter USB to 1 port RS232, RS422, RS485 (software-selectable). RS232 up to 921.6 kbps, RS422/ RS485 up to 3 Mbps.

1. Open Control Panel > Device Manager
2. Plug in your device
3. Locate Universal Serial Bus Controllers > Apple Mobile Device USB Driver.
   It is also possible the device may show under Imaging Devices, Portable Devices or Other Devices or as an MTB USB Device.
4. Right-click and select Update Driver Software...
5. Click Browse my computer for driver software
6. Browse to C:Program FilesCommon FilesAppleMobile Device SupportDrivers or
   C:Program Files (x86)Common FilesAppleMobile Device SupportDrivers
7. Click Let me pick from a list of device drivers on my computer
8. Click Apple Mobile Device USB Driver
9. Click Next, then Close and exit Device Manager

Or try iPhone, iPad, or iPod not recognized in iTunes for Windows - Apple Support

Failing that try a full tear down and rebuild of iTunes as set out in Troubleshooting issues with iTunes for Windows updates.

Download Meilhaus Electronic Port Devices Driver Windows 10

tt2

Jan 21, 2016 7:38 PM

The CH340 chip is used by a number of Arduino compatible boards to provide USB connectivity, you may need to install a driver, don’t panic, it’s easier than falling off a log, and much less painful.

Windows

(Manufacturer’s Chinese Info Link)

1. Download the Windows CH340 Driver
2. Unzip the file
3. Run the installer which you unzipped
4. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.
   

Older Windows Driver Version and Instructions

1. Download the Windows CH340 Driver
   
2. Unzip the folder.
   
3. If you are running a 64Bit Windows: – run the SETUP_64.EXE installer.
   
4. If you are running a 32Bit Windows: – run the SETUP_32.EXE installer.
   
5. If you don’t know, try the 64 bit and if it doesn’t work, the 32 bit.
   
6. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.
   

Macintosh

Download Meilhaus Electronic Port Devices Driver Win 7

(Manufacturer’s Chinese Info Link)

The following github has up to day pkg files for 1.3, 1.4 and 1.5 at time of writing, thanks to Joshua Wallis for bringing this to my attention…

Direct Download Links (from the github repo above):

See the github link above for installation instructions if you need them.

Previous macinstosh downloads if the above doesn’t work for you…

(V1.3) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11) and Sierra (10.12)

Inside the zip file you will find a PDF and a “pkg” file, short version, double click the pkg file, the PDF has some extra information.

OSX Sierra (10.12) Note

A kindly user, Maarten Segers reports

FYI, the driver documented here WILL crash on OSX Sierra.

I can personally not test on MacOS and can not vouch for the above drivers at github, but there you go.

See uninstalling information at the bottom of the page if the driver causes problems for you.

Here is an older version of the Mac driver, NOT FOR 10.12 Sierra

(V1.0) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11)

Linux

(Manufacturer’s Chinese Info Link)

Drivers are almost certainly built into your Linux kernel already and it will probably just work as soon as you plug it in. If not you can download the Linux CH340 Driver (but I’d recommend just upgrading your Linux install so that you get the “built in” one).

Uninstalling From Macinstosh

A couple of Mac users have said “the driver crashes my mac Sierra how do I uninstall”.

Firstly regards the crash make sure you installed the 1.3 version of the driver, not the old one. You could download it directly from the Manufacturers Website in case they have issued an update since I wrote this page.

Secondly a quick google search reveals that this is how you uninstall:

Download Meilhaus Electronic Port Devices Driver Ed

1. Open a terminal and type: cd /Library/Extensions/
2. Verify that the .kext file is present: ls | grep usbserial.kext
3. Output should be: usbserial.kext
4. Then type: sudo rm -R usbserial.kext
5. Verify that the .kext file has been removed: ls | grep usbserial.kext
6. Output should be empty.
7. After you should remove the files stored in receipts folder: cd /private/var/db/receipts/
8. Find the enties: ls | grep usbserial*
9. Output should be: codebender.cc.ch34xinstaller.usbserial.pkg.bom codebender.cc.ch34xinstaller.usbserial.pkg.plist
10. Remove each one of the files of the above list: sudo rm -r filename`